Make-Your-Own Sensor
Turn any switch, button, or third-party sensor into a plug-and-play input for your escape room — the sensor module that connects your own ideas to the ecosystem.




See It in Action
A quick look at the Make-Your-Own sensor module
How It All Connects
See how our products work together to create a complete escape room puzzle
Puzzle Ready!
Complete Setup
Your escape room puzzle is good to go
Make-Your-Own Sensor Features

Attach Your Own Sensor to the Ecosystem
The Make-Your-Own sensor is for those who want to attach their own sensor to the Universal puzzle controller. Push buttons, reed switches, levers, salvaged industrial switches — if it can close a circuit, it can become an escape room sensor.
Compared to cheaper adapters, it gives you the full sensor-module feature set: status diodes, feedback outputs, selectable operating modes, and support for powered electronic sensors.

One Module, Many Sensors
Connect a single sensor — or several. Wire multiple simple sensors in parallel so any one of them triggers the module, or in series so the puzzle reacts only when all of them are triggered at the same time.
Powered electronic sensors are welcome too: the module provides 5V and 12V power rails for third-party motion, vibration, or light sensors.

Status Diodes, Feedback & Relay Options
Yellow and green diodes show at a glance when the sensor is triggered and when the puzzle is won. The feedback slot is powered straight from the puzzle controller — and you can add an external power supply for bigger loads.
Need to control something directly? Connect an external relay to the module and drive an output without any extra hardware.

Add an Indication Light or Output
The sensor module supports an optional indication output that provides visual feedback when your sensor is triggered. Connect a 5V or 12V diode, LED strip, or status light between a power rail and the GND IN slot and it lights up the moment players trigger your sensor.
The maximum load of the feedback connector is 150 mA. If you need to connect something with a higher current load, add an external power supply — then the maximum load increases to 2A.
Monostable & Bistable Mode
The module has dedicated PULSE and TOGGLE inputs — you choose how your sensor behaves simply by where you connect the wire
Monostable Mode (Pulse)
Connect your sensor’s wire to the PULSE input and the module is triggered only while the sensor is actively being triggered — release the button and it returns to its default state automatically.
Best for: buttons and momentary switches, real-time detection puzzles, and Simon Says / Whack-a-Mole game modes.
Bistable Mode (Toggle)
Connect the wire to the TOGGLE input instead and the module latches: one trigger switches it on, the next switches it off — like a light switch.
Best for: switches that should hold their state, multi-step sequences, and props that stay activated once triggered.
The wiki manual includes wiring diagrams for both modes — for simple switches and for 5V/12V electronic sensors.
See the wiring diagrams →Whack-a-Mole & Simon Says Compatible
The module supports Game Modes 6 and 7 — just make sure the sensor you attach is monostable (it stops being triggered once players let go)

How to Enable Mode 6 & 7
For Simon Says (Mode 6) and Whack-a-Mole (Mode 7), connect a monostable sensor to the PULSE input — one that deactivates automatically when players stop interacting with it, like a push button.
These modes use a feedback diode to show players which sensor to trigger next. To make the diode work in these modes, move its wire from GND IN to GND OUT — it takes about a minute:

Step 1: Remove the wire from the GND IN slot using the included screwdriver.

Step 2: Insert the wire into the GND OUT slot and screw it tightly.
Included Items
Sensor ModuleWith screw terminals and Ethernet port for the Universal puzzle controller
Ethernet Cable50 cm / 1.64 ft, for connecting to the puzzle controller
Inspiration for Your Room
Creative ways to use the Make-Your-Own sensor in escape room puzzles
Your Custom Trigger
Wire up a vintage doorbell, an old industrial switch, or a salvaged lever from a flea market. Any mechanical switch becomes a fully functional escape room sensor — perfect for themed rooms where authentic props matter.
Reed Switch Network
Connect several reed switches in series across all the windows and doors of a room. The puzzle solves only when players close every single one — one module, one controller port, one satisfying finale.
Third-Party Electronics
Attach a 5V or 12V motion, vibration, or tilt sensor from any electronics supplier. The module powers it from its own rails and translates its signal into a plug-and-play ecosystem sensor.
Direct Output Control
Use the relay option to skip the controller entirely: a metal sensor wired to the module can switch on an LED strip the moment it’s triggered — great for small standalone effects.
Technical Specifications

Package Contents
- ✓ Sensor module with Ethernet port for connecting with a Universal puzzle controller
- ✓ Ethernet cable (50 cm / 1.64 ft)
| Sensor Inputs | PULSE (monostable) / TOGGLE (bistable) |
|---|---|
| Power Rails | +5V, +12V, GND |
| Feedback Outputs | GND IN (sensor triggered) / GND OUT (puzzle solved, Modes 6 & 7) / GND (constant) |
| Feedback Max Load | 150 mA (2A with external power supply) |
| Status Diodes | Yellow (sensor triggered), green (puzzle won) |
| Compatible Sensors | Simple switches & 5V/12V electronic sensors |
| Connection | Ethernet cable (RJ45) to puzzle controller |
| Hardware Version | HW7 |
Sensor Module Manual
Find wiring diagrams for every scenario — simple sensors, 5V/12V electronic sensors, multiple sensors in series or parallel, feedback diodes, external power supplies, and relays — in our comprehensive knowledge base.
Open Manual →How to Set It Up

Connect your simple sensor: one wire to the PULSE input (or TOGGLE for latching mode), the other to power GND.

Using a powered sensor instead? Wire its signal to the sensor input and its VCC/GND to the module’s 5V/12V power rails.

Connect the module to the Ultimate Universal puzzle controller with the included Ethernet cable and power the controller on.

Optionally add a feedback diode (power rail → GND IN) so players see when the sensor is triggered.
Frequently Asked Questions
What kind of sensors can I connect to the module?
Two kinds: simple mechanical sensors that close a circuit (push buttons, reed switches, levers, toggle switches) and powered electronic sensors that run on 5V or 12V (motion, vibration, tilt, light sensors and similar). The wiki manual has a wiring diagram for each case.
Can I connect multiple sensors to one module?
Yes. Wire them in parallel so any one of them triggers the module, or in series so the module is triggered only when all sensors are activated at the same time.
How do sensors work?
Sensors detect what players do. When a player performs a specific action, the sensor identifies that action and becomes triggered. When all the sensors connected to a puzzle controller are triggered correctly (in a specific way and/or order), the puzzle is solved and the output sets activate.
How many sensors can one puzzle have?
Our hardware lets you attach up to 14 sensors to one puzzle controller (one puzzle). You can use many sensors of the same kind, or make each of them of a different kind — it all depends on your puzzle idea.
What is the maximum load of the feedback connector?
The maximum load of the feedback connector is 150 mA. If you want to connect something with a higher current load, connect an external power supply — then the maximum load is 2A.
Can your sensors be wireless?
From our experience, wireless technology is not reliable enough to be used in escape room puzzles. With cables, you can be sure that triggering a sensor will be detected by the puzzle controller and won’t ruin the experience.
Do sensors require separate power?
Most of our sensors don’t require power unless you want an additional power supply for high current — it is needed in extensions. The Ethernet cable is included and has to be connected to the Universal puzzle controller to work. Then, connect the controller to a power supply.
Ready to Build Your Own Sensor?
Bring your own ideas into the ecosystem — attach any switch or third-party sensor and make it a plug-and-play puzzle input.
Add to Cart




















Valentin Jimenez (verified owner) –
A very useful prop, can combine with other furnisher of props to use with all stuff from this marvelous shop <3
colinemaeva.bocquet (verified owner) –
easy to set up and to connect to the rest. Loved it. Awsome !